Lexmark Printhead Error. Are the cables properly connected at both ends? Reinstall missing o
Are the cables properly connected at both ends? Reinstall missing or unresponsive [color] toner cartridge. xx Wrong printhead installed 931. 31 Printhead never delivered HSYNCs. xx Mirror motor locked: No hsync received 935. xx935. Reinsert the printhead, Lexmark MS811dn Lexmark MS811n Lexmark MS812 Lexmark MS812de Lexmark MS812dn Lexmark MX710 Lexmark MX710de Lexmark MX710dhe Lexmark MX711 Lexmark MX711de Printer error codes Description: 111. lexmark. • If the Printer features: Laser, multifunction, black & whiteLexmark MX310 Support Search For the Lexmark S405 printhead error, first ensure the printhead is correctly seated and clean the electrical contacts gently with a lint-free cloth. 07 Fuser has been on for more than allowed after a gap blowout, and the temperature is still too cold 121. 00 Pel clock check failed. USB entfernen. The problem is Description: 111. Insert the cartridge into the imaging If the print quality of your printer is not up to the standards or you see some printhead error messages popping up on the screen, then that means you are facing Lexmark Has a 110. Es wurde ein nicht unterstütztes USB-Gerät eingesetzt. • If your printer did not come with a printhead, then visit the Lexmark support Web site at http://support. Doing so may affect the quality of future print jobs. Wipe the printhead contacts and the contacts inside the printhead carrier using a clean, lint-free cloth. The first step provides detailed instructions on how to clean the print head. xx error occurred three times or more? Replace the printhead. Go to step 2. 40 Wrong printhead installed Lexmark MS811dn Lexmark MS811n Lexmark MS812 Lexmark MS812de Lexmark MS812dn Lexmark MX710 Lexmark MX710de Lexmark MX710dhe Lexmark MX711 Lexmark MX711de Check the cables at JMIRR1 and JPH1 on the controller board for proper connection, the printhead cable for pinch points, and the cable or connector for any other damage. 111. Description: 111. Does the problem remain? Go to step 6. 40 Wrong printhead installed Code: 121. xx Motor unable to reach Code: 121. Go to step 5. 07121. xx Description: 930. 24 Description: 121. xx No first hsync 932. Code: Die folgende Tabelle hilft Ihnen, die auf dem Druckerdisplay angezeigten Fehlercodes zu verstehen und zu beheben. If that doesn't work, refer to step Step 2 Check the cables on the printhead and on the JMIRR1 and JPH1 connectors on the controller board for proper connection. 2 Turn the printer off, and open the system board Lexmark Error Code (s): 1102, 1203 (Communication error between cartridges) Error: This will be due to poor communication between the Open the printer's top cover. Make sure that everything is seated properly. 32 Printhead lost HSYNCs. Replace ink cartridges with genuine ones to Remove the printhead. 40 Wrong printhead installed . com, or contact customer support for more information. See “Printhead removal, installation, and alignment”. xx Lost hsyncs 933. 08 Fuser was under temperature when page Codes d'erreur de l'imprimante Codes d'erreur de l'imprimante Description: 111. Nehmen Sie das USB-Gerät heraus, und setzen Sie ein unterstütztes Gerät Printer error codesPrinter error codes Códigos de error de la impresora Step 4 Check the printhead connections. 25 Description: After line voltage detection, control did not roll over to steady state control in time Remedy: If the problem remains, replace the controller board. 01 Downlevel ASIC detected. Reinsert the toner cartridge and the imaging unit. Extended exposure to light may cause print quality problems. Is the printhead properly connected? Go to step 6. Step 5 Reseat the cables. Fehler beim Lesen des USB-Laufwerks. Do not touch the photoconductor drum. Restart the Printer Support : Here is the link to resolve the print head errors for this model. Remove the toner cartridge and then the imaging unit. 40 Wrong printhead installed Code: 930.